Why does my Maytag washer say Loc? (2024)

Answer

LoC or LC – Front Load Washer. This error code does not mean “Door Locked”. The door will open when the control is locked, but the washer will not start, due to control being locked.

Accordingly, what does loc mean on Maytag washer?

Control Lock

Subsequently, question is, how do I unlock my Maytag dryer?

Press and hold for 3 seconds the “Control Lock/Unlock” button on the control panel to unlock the control panel. The “Control Lock” status light is goes out when the control panel is unlocked. In addition to Oldturkeys answer, try unplugging it for five minutes to allow it to reset.

Similarly one may ask, how do I take the lock off my Maytag washer?

To unlock the controls, press and hold the CYCLE END SIGNAL for 3 deliberate seconds or until the control lock light goes out. If the control locked light will not turn off, I recommend unplugging the washer for 5 minutes.

How do you reset the key on a Maytag commercial washer?

Unplug the washer for 1 minute from the electrical outlet.

Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.

26 Related Question Answers Found

What does it mean when my Whirlpool washer says Loc?

If the control lock has been activated, the control will not function. If you try to push buttons, you may see the code “LoC” or “LC” (depending on your model) (depending on your model). This is a reminder that you have set the control lock, and need to de-activate it to allow the washer controls to function.

What does it mean when my Whirlpool washing machine says control lock?

Select and hold END OF CYCLE SIGNAL for 3 seconds until the CONTROL LOCKED Status light turns off. If that does not do it, try putting the machine into diagnostic mode. The washer must be empty and the control must be in the OFF state before pressing the touch-pad sequence to start the test.

How do I turn off the control lock on my Whirlpool washer?

How to Unlock the Controls for a Whirlpool Duet Washer Locate the “Control Lock/Unlock” button on your Duet’s control panel. Press and hold the “Control Lock/Unlock” button for three seconds. Release the “Control Lock/Unlock” button when the control lock icon on the display disappears.

Why does my Whirlpool washer not start?

If the door lock is defective, the washer will not spin or start. If the door lock is damaged or does not latch properly, replace it. To determine if the door lock has failed electrically, consult your washer’s wiring diagram and use a multimeter to test each of the door lock switches for continuity.

How do you unlock the controls on a Maytag oven?

Door is locked when starting or using the oven Press Cancel/Off key to start a latch reset, wait 20-30 seconds and open door. Turn the power off at the circuit breaker or fuse box for one minute, then turn the power back on.

How do you unlock the control lock on a Whirlpool Duet washer?

How do I unlock my Whirlpool front load washer?

Hold down the “Control Lock” button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.

What is control lock on washer?

The Control Lock feature on Front Load Washers can prevent any selections from being made when activated. The controls can be locked or unlocked after a cycle has started. To lock or unlock the washer controls: Press and hold the LOCK button for 3 seconds.

How do you fix a Maytag lid lock?

How to Replace the Lid Lock on a Maytag Vertical Modular Washer . Repair Difficulty. [00:09] Shut off the electricity and water. [00:55] Remove screws from the back. [01:08] Release the lid lock from the top panel. [01:36] Open the control console. [02:05] Disconnect the wire harness from the control board. [02:27] Attach the wire harness for the new lid lock. [02:52] Step 12: Lower the top panel. [03:09]

How do I reset my Whirlpool top load washer?

Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.

Is there a reset button on a Maytag dryer?

One thing that Maytag dryers do not have, however, is a reset button. It is possible to reset the dryer through a few steps.

Why does my Maytag dryer not start?

On most dryers the drive motor turns the drum and the blower wheel to exhaust the air. If the dryer won’t start the motor might be defective. Before replacing the motor, check the thermal fuse, start switch and door switch because all three are more likely the cause.

Is there a reset button on a Maytag Centennial dryer?

One thing that Maytag dryers do not have, however, is a reset button. It is possible to reset the dryer through a few steps.

ncG1vNJzZmivp6x7r6%2FEq6upp5mjwW%2BvzqZma2hiZ3xxfY6wn7JllKSytHnMsmSmmamprqh51pqqoZ2iYsCixYylppxmmKm6rQ%3D%3D

Christie Applegate

Update: 2024-06-19

<< 4 Extremely Bizarre Ways Eccentric Billionaires Have Spent Their MoneyWhat is Host and Comedian Tone Bells Net Worth? >>